IJSTR

International Journal of Scientific & Technology Research

Home About Us Scope Editorial Board Blog/Latest News Contact Us
0.2
2019CiteScore
 
10th percentile
Powered by  Scopus
Scopus coverage:
Nov 2018 to May 2020

CALL FOR PAPERS
AUTHORS
DOWNLOADS
CONTACT

IJSTR >> Volume 9 - Issue 11, November 2020 Edition



International Journal of Scientific & Technology Research  
International Journal of Scientific & Technology Research

Website: http://www.ijstr.org

ISSN 2277-8616



Health Status Of Workers In Furnace Operation On Foundry Task

[Full Text]

 

AUTHOR(S)

Das Chandan, Das Suman, Banerjee Debamalya, Samanta Amalendu, Bhattacharyya Bidyut Kumar

 

KEYWORDS

Discomfort feelings, Health status, Posture analysis, OWAS, RULA, Stress analysis

 

ABSTRACT

The principle targets of this investigation were to recognize the trickiest stances in pounding undertakings performed at foundry, located at Howrah in West Bengal through utilization of the RULA, OWAS strategy and to create proposals for development of working techniques and working environments. Seventeen skilled laborers, with mean age of 42.6, from three foundry partook in the field study. The furnace tasks undertakings during the three-month time frame for this study. Significant distributions and material on Work-related body-part inconvenience assessment procedures have been gathered for consideration in this investigation and measure the logical writing on observational strategies. Self-assessment of laborers can be utilized to gather information on work environment introduction to physical components by utilizing strategies that incorporate specialist meetings and polls. As observational strategies are more inescapable than self-rating - based methods and can be used as a useful device in the work environment, The reason for every order is sketched out and estimated in evaluating the seriousness, recurrence, and term of business related physiological uneasiness, and fuses a significant number of the key qualities distinguished in this writing investigation.

 

REFERENCES

[1] Hignett, S. and McAtamney, L 2000 Rapid Entire Body assessment (REBA) Applied Ergonomics, 31, 201-205.
[2] Karhu, O., Kansi, P., and Kuorinka, I. 1977.Correcting working postures in industry: a practical method for analysis. Applied Ergonomics, 8(4), 199 201.
[3] D.C. Metgud, M.G. Mokashi, P.N. Saha, Subhash Khatri. An Ergonomics study of women workers in a woollen textile factory for identification of health-related problems.
[4] Aaras, A, G. Horgen, M. Helland. Can visual discomfort influence on muscle pain for visual display unit (VDU) workers.
[5] Rongo LM, et al. Occupational exposure and health problems in small-scale industry workers in Dares Salaam, Tanzania: a situation analysis. Occup Med (Lond), 2004; 54(1):42–6
[6] Markku Mattila, Waldemar Karwowski & Mika Vilkki. Analysis of working postures in hammering tasks on building construction sites using the computerized OWAS method. Applied Ergonomic,24(6): 405-412 (1993)
[7] Ali, A.,Qutubuddin, S.M.,Hebbal, S.S. and Kumar, A.C.S.(2011) “An Ergonomic Study of Work Related Musculoskeletal Disorders Among the Workers Working in Typical Indian Saw Mills” Intentional Journal of Engineering Research and Development, Vol.3, pp.38-45.
[8] Varmazyar Sakineh, et.al., “Evaluation Working posture and Musculoskeletal Disorders Prevalence in Pharmacy packaging Workers”, European Journal of Scientific research ISSN 1450-216X vol.29 No. 1(2009), pp82-88
[9] Widanarko, B., Stephen L., Stevenson, M., Devereux, J., Cheng, S. and Pearce, N. (2012) “Prevalence and work-related risk factors for reduced activities and absenteeism due to low back symptoms”, Applied Ergonomics, Vol. 43, pp. 727-737
[10] Wearsted, M. Westgaard, RH. (1991)Working hours as a risk factor in the development of musculoskeletal complaints; Ergonomics Vol. 34(3) pp.265–76
[11] Jaspreet Singh et al., “Musculoskeletal Disorder Risk Assessment in Small Scale Forging Industry by using REBA Method” International Journal of Engineering and Advanced Technology, Volume-1,Issue-5, June 2012.
[12] Jones, T. and Kumar S.(2010) “Comparison of ergonomic risk assessment output in four saw mill jobs” International Journal of Occupational Safety and Ergonomics, Vol. 16, No. 1, pp.105– 111.
[13] Markku, M., K. Waldemar , and V. Mika.1993 “Analysis of working postures in hammering tasks on building construction sites using the computerized OWAS method.” Applied Ergonomics 24(6): pp 405-412.
[14] Metan, S., G. C. Mohan kumar, and P. Krishna. 2016.“FEM an Effective Tool to Analyse the knee Joint Muscles during Flexion” American Journal of Biomedical Engineering 6(2): pp 43-52
[15] Rongo L.M, et al. 2004.“Occupational exposure and health problems in small-scale industry workers in Dares Salaam, Tanzania: a situation analysis”. Occupational Med (Lond), 54(1):42–6
[16] Singh, J. et al., 2012 “Musculoskeletal Disorder Risk Assessment in Small Scale Forging Industry by using REBA Method” International Journal of Engineering and Advanced Technology, Vol-1,Issue-5.
[17] Swangnetr, M., P. Namkorn, C. Phimphasak, K.Saenlee, D.Kaber, O.Buranruk, et al.2012. “Ergonomic analysis of rice field ploughing” 1st ed. Boca Raton F, USA: CRC Press LLC:. Chapter 64 Advances in Physical Ergonomics and Safety PP. 565-574.